East Coast Enduro Association: BRAND NEW STILL IN THE ORIGIBNAL BAG ACERBIS REAR TAILIGHT WITH LICENSE PLATE HOLDER! - East Coast Enduro Association

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • This topic is locked

BRAND NEW STILL IN THE ORIGIBNAL BAG ACERBIS REAR TAILIGHT WITH LICENSE PLATE HOLDER! EITHER PICK IT UP OR PAY FOR SHIPPING!

#1 User is offline   SCOTT SIEGMEISTER 

  • Junior Member
  • PipPipPipPipPipPipPipPip
  • Group: ECEA - Club Member
  • Posts: 798
  • Joined: 31-August 01
  • Gender:Male
  • Interests:MOTORCYCLES,SKIING,FISHING AND GUNS

Posted 03 February 2011 - 09:54 PM

I promised this to Mike Walters, I suppose to send it out and then I got very busy with work. I was away most of last week and forgot to send it to him before I left. I sent Mike an e-mail saying that I was sorry and asked him if he still wanted it, he told me since he didn't hear back from me, he went out and bought one.

If anyone is looking for one, let me know and we can work out the details for pickup or shipping.

Regards,

Scott

P.S. Sorry again Mike
0

#2 User is offline   David Stanwood 

  • Board Charter Member
  • PipPipPipPip
  • Group: ECEA Member
  • Posts: 54
  • Joined: 08-September 09
  • Gender:Male
  • Location:Chatsworth, NJ

Posted 03 February 2011 - 11:30 PM

If it's an LED one I'll take it. Was just going to order an LED one next week because my standard bulb is pulling to much power and causing my lights to dim.
0

#3 User is offline   SCOTT SIEGMEISTER 

  • Junior Member
  • PipPipPipPipPipPipPipPip
  • Group: ECEA - Club Member
  • Posts: 798
  • Joined: 31-August 01
  • Gender:Male
  • Interests:MOTORCYCLES,SKIING,FISHING AND GUNS

Posted 05 February 2011 - 03:01 PM

Sorry it is the standard bulb.
0

#4 User is offline   David Stanwood 

  • Board Charter Member
  • PipPipPipPip
  • Group: ECEA Member
  • Posts: 54
  • Joined: 08-September 09
  • Gender:Male
  • Location:Chatsworth, NJ

Posted 05 February 2011 - 10:48 PM

OK thanks,
0

#5 User is online   stephen mason jr. 

  • Board VIP
  • PipPipPipPipPip
  • Group: Members
  • Posts: 229
  • Joined: 12-March 08
  • Gender:Male
  • Location:clayton nj

Posted 06 February 2011 - 09:48 AM

ill take it if its still available,let me know the shipping
steve
0

#6 User is offline   SCOTT SIEGMEISTER 

  • Junior Member
  • PipPipPipPipPipPipPipPip
  • Group: ECEA - Club Member
  • Posts: 798
  • Joined: 31-August 01
  • Gender:Male
  • Interests:MOTORCYCLES,SKIING,FISHING AND GUNS

Posted 08 February 2011 - 09:19 AM

Hi Stephen, I am sorry but as soon as I reposted it, someone contacted me and I told them that they can have it.

Regards,

Scott
0

#7 User is offline   Tammy Redstone 

  • "Has too much time at work to surf the Internet"
  • PipPipPipPipPipPipPipPip
  • Group: Members
  • Posts: 361
  • Joined: 29-September 10
  • Gender:Female
  • Location:Bergen Co, NJ
  • Interests:Riding.

Posted 13 February 2011 - 09:29 AM

View PostDavid Stanwood, on 03 February 2011 - 11:30 PM, said:

If it's an LED one I'll take it. Was just going to order an LED one next week because my standard bulb is pulling to much power and causing my lights to dim.


Dave you can replace a standard bulb with a LED bulb for under 10.00 and if it is just a tail light and you need both stop and tail all you need is a Resistor and two 1N4007 Diodes and a stop light switch and your good to go..
0

#8 User is offline   David Stanwood 

  • Board Charter Member
  • PipPipPipPip
  • Group: ECEA Member
  • Posts: 54
  • Joined: 08-September 09
  • Gender:Male
  • Location:Chatsworth, NJ

Posted 16 February 2011 - 02:11 PM

View PostTammy Redstone, on 13 February 2011 - 09:29 AM, said:

View PostDavid Stanwood, on 03 February 2011 - 11:30 PM, said:

If it's an LED one I'll take it. Was just going to order an LED one next week because my standard bulb is pulling to much power and causing my lights to dim.


Dave you can replace a standard bulb with a LED bulb for under 10.00 and if it is just a tail light and you need both stop and tail all you need is a Resistor and two 1N4007 Diodes and a stop light switch and your good to go..


Sorry Tammy I just saw this. I did pickup an LED bulb just the other day. Thanks for your help.
0

#9 User is offline   SCOTT SIEGMEISTER 

  • Junior Member
  • PipPipPipPipPipPipPipPip
  • Group: ECEA - Club Member
  • Posts: 798
  • Joined: 31-August 01
  • Gender:Male
  • Interests:MOTORCYCLES,SKIING,FISHING AND GUNS

Posted 05 January 2012 - 10:37 PM

If anyone needs this, I still have it.
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • This topic is locked

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users